MORENO WITHOUT RISER + BALUSTRADE

MORENO STAIRCASE WITHOUT RISER + BALUSTRADE

Traditional MORENO staircase in fir, with or without risers.

Straight staircase MORENO Fir

€438.87

2 In stock Dispatched within 10 days

Riser

Handrail

PENDEDIS Wood Spindle Balustrade for MORENO and SUCHET Staircases

€139.13

2 In stock Delivered to you in 10 days

€577.99 incl. tax

Including €1.47 for ecotax

In stock Dispatched within 10 days

Quantité

Pack contents

Straight staircase MORENO Fir
PENDEDIS Wood Spindle Balustrade for MORENO and SUCHET Staircases

Straight MORENO staircase in solid fir — cuttable kit up to 285 cm. 15 treads, width 80 cm (82 cm with handrail), section 200x28 mm, recommended stairwell 85x273 cm. Available with or without risers and with or without included handrail. Raw solid fir delivered untreated — to be oiled, varnished, or stained before installation. Floor footprint 273 cm. Fixings and assembly instructions included. For interior use only — untreated fir is not suitable for exterior use or damp environments.

Straight Fir Staircase MORENO - Cuttable Kit 285 cm, 15 Treads

The straight staircase MORENO in solid fir is delivered as a kit for on-site assembly, with a maximum floor-to-floor height of 285 cm and 15 treads (including a flush landing tread). Its cuttable design allows the height to be adapted to the actual site configuration, within the limit indicated in the instructions. The width excluding handrail is 80 cm (82 cm with handrail), for a recommended stairwell opening of 85x273 cm. Tread height: 19 cm. Going: 18.3 cm. Tread section: 200x28 mm with risers, 220x28 mm without riser.

The fir is supplied untreated: a protective finish suitable for interior use must be applied after installation. The model is available with or without risers and with or without a handrail, depending on the version ordered. The fixing screws are not supplied and must be chosen according to the substrate (concrete, timber, etc.). The floor footprint of 273 cm must be verified before ordering, taking into account finished floor coverings and ceiling finishes.

Main specifications

Specification	Description
Type	Straight staircase, interior, cuttable kit
Timber species	Untreated natural fir
Max. floor-to-floor height	285 cm (cuttable per instructions)
Number of treads	15 (including 1 flush landing tread)
Tread height	19 cm
Going	18.3 cm
Width	80 cm without handrail / 82 cm with handrail
Tread section	200x28 mm (with risers) / 220x28 mm (without riser)
Floor footprint	273 cm
Recommended stairwell opening	85x273 cm
Risers	With or without, your choice
Handrail	Optional — can be added after installation, reversible left or right
Finish	Raw timber, to be treated after installation
Use	Interior use only

Packaging

✓ 2 parcels: standard delivery

Packaging

Version with risers and spindle handrail (width 80 cm)

✓ Parcel 1 — Stringers, handrail, bottom newel post, top newel post | 24x410x13 cm | 35 kg
✓ Parcel 2 — 15 treads + 15 risers | 46x78x33 cm | 40 kg

Notched version without handrail, without riser (width 80 cm)

✓ Parcel 1 — Stringers | 405x23x7 cm | 20 kg
✓ Parcel 2 — 15 treads | 79x45x25 cm | 20 kg

Key points

✓ Cuttable: adaptation to floor-to-floor height up to a maximum of 285 cm, in accordance with the instructions provided.
✓ Kit assembly: elements delivered unassembled for on-site fitting — instructions included.
✓ Combinable options: version with or without risers, with or without handrail, independently of each other.
✓ Mandatory finish: the raw fir must receive a protective treatment (oil, varnish or interior paint) before first use.
✓ Interior use only: access to upper floor, mezzanine, loft.

Installation advice

Checking dimensions: verify the floor-to-floor height (maximum 285 cm) and the available stairwell opening (85x273 cm recommended) before unpacking the kit. These measurements must be taken on finished floors and ceilings, including coverings.

Cutting: if the floor-to-floor height is less than 285 cm, cut the stringers from the bottom according to the cutting chart provided. Cutting modifies the height of the first tread. Always check the result before final assembly.

Assembly: assemble the stringers, treads and risers according to the instructions provided, then fix securely to the floor and the upper support. A minimum of two people is required to handle the stringers.

Anchoring: fix the stringers to the floor and the support using fixings suitable for the material (concrete, timber, etc.). Fixings are not supplied — allow for suitable wall plugs for the substrate.

Handrail: the handrail can be installed after the staircase has been fitted. It is reversible — can be fitted on the right or left when going up, depending on your configuration.

Maintenance and protection

The raw fir delivered must imperatively receive a protective finish before first use to limit wear marks and make maintenance easier. Recommended options:

✓ Aqua-polyurethane staircase varnish: 2 to 3 coats, maximum resistance, renewal every 5 to 7 years
✓ Oil-wax: natural matt finish, maintenance every 1 to 2 years
✓ Interior paint: personalise the colour, minimum 2 coats

Routine cleaning: slightly damp cloth, pH-neutral product. Avoid standing water on the treads. Check the tightness of fixings once a year.

WoodUp tip

Before cutting the stringers, always check the floor-to-floor height on finished floors and ceilings — including floor covering, parquet, tiles and suspended ceilings. An error of a few centimetres when taking measurements can render the staircase uncuttable once the stringers are too short.

Good to know before buying: the spindle handrail can be added after the staircase has been installed — reversible left or right. You can therefore order the staircase without a handrail and add one later if needed.

Frequently asked questions

How do I cut the MORENO staircase to my floor-to-floor height?

Cutting is carried out on the stringers from the bottom, according to the cutting chart provided in the instructions. Each centimetre removed modifies the height of the first tread. For a floor-to-floor height of 270 cm, for example, the cut is approximately 15 cm per stringer. Use a guided circular saw and work on both stringers simultaneously to ensure a perfectly level result.

What is the difference between the version with and without risers?

With risers, the staircase is closed: the vertical faces between the treads are clad, the structure looks visually fuller and lets less dust through. Without risers, the staircase is open, visually lighter and allows light to pass through. Both versions use the same stringer; only the tread section changes (200x28 mm with / 220x28 mm without).

Is the 85x273 cm stairwell opening a minimum or a recommended dimension?

This is a recommended dimension for comfortable fitting with installation tolerances. The strict minimum dimension is the staircase footprint (273 cm) + width (80 cm). In practice, allowing an extra 5 cm in width and 2 cm in length makes it easier to adjust plumb without constraint.

Which staircase should I choose for a mezzanine with a floor-to-floor height of 260 cm?

The MORENO is suitable: it can be cut to 260 cm without difficulty (a cut of approximately 25 cm on the stringers). For heights below 240 cm, the loft staircases AULAC or BASSEYRE, which are more compact, may be better suited depending on the available floor space.

Should fir be treated before or after installation?

The finish is applied after complete installation, once the staircase is fixed in place. If a handrail is planned, it can be fitted before or after finishing depending on your workflow. Treating before installation risks clogging the assembly areas and preventing adjustments. However, the hidden faces (undersides of treads, inner faces of stringers) can be treated before assembly for complete protection.

Why choose the MORENO rather than a quarter-turn staircase?

The straight staircase MORENO is suitable when the stairwell opening is rectangular and aligned along the length of the staircase, with no change of direction. It is simpler to install and more affordable. A quarter-turn staircase is necessary when the available floor space does not allow the full footprint (273 cm) to be aligned in a straight line, or when the room layout requires a change of direction.

Our complementary staircases

NUGERE — Space-saving staircase with alternating treads, compact footprint

CHEVALARD — Straight staircase in beech or fir, Standard range

FONTBRUNO oak — Straight staircase in glued laminated oak, 14 treads

Data sheet

Width (cm): 80
Species/material: Fir
Number of treads: 15
Section (mm): 220*28 (without riser)
Section (mm): 200*28 (with risers)
Footprint (cm): 273
Recommended stairwell opening (cm): 85*273
Floor-to-floor height (cm): 285
Step height (cm): 19
Range: Standard
Tread depth (cm): 18.3
Staircase type: Straight

PENDEDIS wood spindle balustrade for MORENO and SUCHET staircases. Complete dimensions: handrail 3900 x 60 x 50 mm, 17 spindles 800 x 55 x 20 mm, bottom rail 3900 x 50 x 40 mm, 2 newel posts 1050 x 60 x 60 mm included. Raw untreated wood, to be varnished (2 coats for the handrail) or painted before use. Complete kit with all sections dimensioned for this staircase – check spindle spacing is less than 11 cm.

PENDEDIS wooden baluster balustrade for MORENO and SUCHET staircases

The PENDEDIS balustrade is a complete straight wooden baluster handrail designed for the MORENO and SUCHET staircases. It consists of a handrail, straight balusters, a bottom rail and newel posts, forming a coherent and secure assembly for your interior staircase.

Precise dimensions: handrail 3900 x 60 x 50 mm, balusters 17 x 800 x 55 x 20 mm, bottom rail 3900 x 50 x 40 mm, newel posts 2 x 1050 x 60 x 60 mm. Delivered raw and untreated.

Main features

Feature	Description
Compatibility	MORENO and SUCHET staircases
Handrail	3900 x 60 x 50 mm
Balusters	17 straight balusters 800 x 55 x 20 mm
Bottom rail	3900 x 50 x 40 mm
Newel posts	2 newel posts 1050 x 60 x 60 mm
Finish	Raw wood - to be painted, varnished or stained
Use	Indoor

Key points

✓ Precise dimensions: handrail 3900x60x50 mm, 17 balusters 800x55x20 mm
✓ Complete kit: handrail, balusters, bottom rail and newel posts included
✓ Compatible with MORENO and SUCHET: dimensioned for these two straight staircase models
✓ Sturdy newel posts: 60x60 mm for solid fixing to the floor and step
✓ Raw wood: customisable with paint, varnish or wood stain

Installation advice

Check compatibility with your MORENO or SUCHET staircase before ordering. Start by fixing the bottom newel post (at the bottom) and top newel post (at the top) into the steps or floor according to the instructions. Then position the bottom rail and distribute the 17 balusters evenly between the newel posts. Finish with the handrail.

Apply the chosen finish before final fixing to also treat the embedded parts. The handrail requires an abrasion-resistant finish (varnish 2 coats recommended).

Maintenance and protection

The wood is delivered raw and untreated. Apply a protective finish before intensive use - satin varnish (2 coats), oil-wax or polyurethane varnish depending on the desired appearance. The handrail, subject to frequent contact, particularly benefits from an abrasion-resistant varnish.

Annual maintenance with a product suited to the chosen finish is sufficient to preserve the appearance of the wood. Avoid abrasive products or solvent-based cleaners that degrade finishes.

Frequently asked questions

What is the difference between the PENDEDIS balustrade and the MONTJARDIN handrail?

The PENDEDIS is a complete balustrade with precise dimensions (handrail 3900 mm, 17 balusters, bottom rail, 2 newel posts) designed for MORENO and SUCHET staircases. The MONTJARDIN is a cuttable-to-size handrail designed for the FAGEOLE staircase. The PENDEDIS is simpler to install as it is already dimensioned for its staircase; the MONTJARDIN is more flexible but requires adaptation.

Is the PENDEDIS kit compatible with the MORENO staircase in fir and in beech?

The PENDEDIS is compatible with both versions of the MORENO staircase (fir and beech) and SUCHET, which share the same structural dimensions. The timber species of the balustrade may differ from that of the staircase - choose according to the desired aesthetic and apply the same finish for visual harmony.

Do the 17 balusters of the PENDEDIS comply with the safety standard (passage of an 11 cm sphere)?

The spacing between the balusters must be less than 11 cm to prevent the passage of an 11 cm sphere (standard NF P01-012). With 17 balusters over 3900 mm, check the actual positioning according to your staircase. If the MORENO/SUCHET staircase has a different stairwell opening, adjust the spacing accordingly before final fixing.

Can the PENDEDIS be installed on both sides of the MORENO staircase?

The MORENO staircase is a straight staircase with a handrail on one side in its standard configuration. If you want a handrail on both sides (double handrail configuration), order two PENDEDIS kits and adapt the wall fixing for the side without a newel post.

How long does it take to install the PENDEDIS balustrade?

An experienced DIY enthusiast can install the PENDEDIS in 2 to 4 hours (excluding finishing). You will need a drill, wood and metal drill bits, a spirit level, a mitre saw for angle cuts, and fixings suited to your steps. The finish (varnish or paint) requires additional drying time between coats.

See all our wooden baluster handrails